- 4X4 ACTUAL SIZE INSTALL
- 4X4 ACTUAL SIZE CODE
- 4X4 ACTUAL SIZE FREE
For hard to clean surfaces, use a deck brightener containing oxalic acid and follow the manufacturer’s instructions to retain the wood’s natural beauty.Liquid detergents, water and a stiff bristle brush will remove most mildew and dirt.
4X4 ACTUAL SIZE FREE
To provide long term aesthetic appeal for your deck or outdoor project, keep it free of dirt and debris, and apply a water repellent sealer every two years after initial staining and sealant are applied. Always follow finish manufacturer’s application instructions. Apply a high-quality oil or water-based finish with UV protection and water repellent to slow down the process of wood turning gray from exposure to the sun. As soon as the wood is porous enough to accept the stain, it is ready to stain. Apply the finish to a small portion of the deck to ensure that the wood is sufficiently dry. Test the wood with a few drops of water to see if the wood is dry enough to readily absorb the water. After installation, allow the wood to dry prior to applying any finish. Keep it looking its best with the right wood and deck cleaners, sealers and stains to enhance its long-term beauty. Your outdoor project or deck should last for years. Care for Your Pressure-Treated Wood Project. Treated wood may be disposed of in landfills or burned in commercial or industrial incinerators or boilers in accordance with federal, state and local regulations. Do not use pressure-treated wood for mulch. Do not use pressure-treated wood in circumstances where the preservative may become a component of food, animal feed or beehives. Pressure-treated wood should not be used where it may come into direct or indirect contact with drinking water, except for uses involving incidental contact such as fresh water docks and bridges. Wash work clothes separately from other household clothing before reuse. All sawdust and debris should be cleaned up and disposed of after construction in accordance with local waste management regulations. Wash hands thoroughly with mild soap and water after working with treated wood. Wear appropriate eye protection to reduce the potential for eye injury from wood particles and flying debris during machining. 
Wear a dust mask when machining any wood to reduce the inhalation of wood dusts. Safe Practices When Working with Pressure-Treated Wood. 4X4 ACTUAL SIZE CODE
Click here to see Glenn Mathewson, building code educator, author and consultant, videos for more details on basic design and construction methods for residential wood decks and significant changes in the current International Residential Code. 4X4 ACTUAL SIZE INSTALL
Install the un-cut end of support posts in ground contact applications. Install fasteners flush to the wood surface. Use screws to improve holding performance. Pre-drill holes at the ends of boards to help prevent splitting. Butt boards tightly together during installation as they will shrink slightly in width and thickness as they dry out. 
Place the best-looking side of a deck board face up. Deck stains and sealers do not provide adequate protection. Copper naphthenate formulations are available from home centers, lumber dealers and hardware stores. For exterior project applications, treat all field-cut ends of boards and drilled holes with a brush-on wood preservative. For permanent wood foundations and corrosive environments, such as areas with saltwater spray, stainless steel fasteners are recommended. 
Direct contact of Preserve®CA treated wood with aluminum products is not recommended.Ecolife can be used in direct contact with aluminum products, including flashing, even in continuously wet applications.Caution: Do not mix metals: Use stainless-steel fasteners with stainless-steel connectors and galvanized fasteners with galvanized connectors.Type 316 or higher is recommended for exposure to salt or saltwater. Type 304 or higher stainless steel is recommended for very wet environments such as poolside deck. Stainless steel offers the best protection.For coastal installations, use code approved stainless steel.Hot-dipped galvanized steel is recommended and should conform to ASTM A153 for fasteners and ASTM A653, G185 for connectors.For the best results, use building-code approved, corrosion-resistant fasteners and connectors for all exterior wood projects.All other members (including all 6x's, 8x's, 10x's, etc. Note: Anything greater than or equal to a: 1x8, 2x8, 3x8 or 4x8 will take 3/4" off the planing in the strong axis. Table 1: Sawn Lumber Nominal vs Actual Size + Weights
0 kommentar(er)
